How To Set Up A Keg
How to Prepare Up a Kegerator
Last updated on seven/01/2020
Afterwards y'all've deliberated and chosen the best kegerator for your business concern, it's time to set up your beer dispenser and start serving fresh, common cold beer! Nosotros've got stride-by-step directions and an instructional video to assistance you through the process, allowing yous to pour the perfect pint. Employ our steps as a full general guideline, simply always refer to your equipment manual for the manufacturer's specific instructions.
Shop All Beer Dispensers
1. Unpackage the Kegerator
- Remove all the packaging from your kegerator.
- If the unit of measurement has been transported on its side, let the unit stand up upright for at least 24 hours earlier plugging it in.
- Movement the unit of measurement to its final location and install it on a level surface.
- Make certain to provide clearance effectually the unit for ventilation, per the manufacturer's instructions.
ii. Install the Draft Belfry
In one case your kegerator is unpackaged and placed in its final location, y'all tin begin installing the typhoon belfry. Gather your materials and expect for the circular opening on top of the unit.
Y'all'll demand the following materials:
- Rubber washer
- Typhoon tower
- Beer line
- 4 mounting screws
- Air hose
- Tap faucet handle
Follow these steps:
- Identify a prophylactic washer on summit of the circular opening.
- Feed the beer line down through the opening into the interior cabinet.
- Identify the typhoon belfry on superlative of the opening and secure it with four mounting screws.
- Feed the air hose into the draft tower from inside the chiffonier.
- The air hose helps to keep the beer cold as it travels up the beer line.
- Screw the tap handle onto the tap faucet.
- Connect the tap faucet to the draft belfry.
3. Connect Beer and Gas Lines
You'll need 2 lines to gear up your kegerator - the beer line and the gas line. The beer line connects to the keg past way of the keg coupler and delivers cold beer to the tap faucet. The gas line connects to the CO2 regulator on the CO2 tank, then too connects to the keg coupler.
Depending on the manufacturer of your unit, you may need to buy some of these required beer dispensing components separately. Refer to your kegerator transmission for more than information.
Yous'll demand the following materials:
- (2) Rubber washers
- Nut
- Keg coupler
- Beer line
- Gas line
- Beer keg
- CO2 tank
- CO2 regulator
Follow these steps:
- Keep the tank upright at all times.
- Attach the beer line to the keg coupler, placing a rubber washer at the connectedness signal.
- Attach the gas line to the CO2 regulator output barb and tighten screw clamp.
- Connect the other end of the gas line to the keg coupler and tighten spiral clench.
- Using a safety washer and nut, adhere the CO2 regulator to the CO2 tank.
- Spiral the coupler onto the keg.
- When the coupler is fitted into place, button the coupler handle downward to open the seal.
- Identify the keg inside the kegerator.
4. Conform the CO2 Regulator
With your beer and gas lines in identify, y'all're almost ready to start dispensing your customers' favorite beers. You'll just need to make some adjustments to your CO2 tank and regulator to release the gas and make sure information technology's at the correct pressure level.
Follow these steps:
- Plow the handwheel on the CO2 regulator to the left to open the air tank.
- Flip the shut-off valve on the regulator to ON.
- You should hear air enter the gas lines.
- Adjust the PSI and so the pressure gauge reads between 10 and 15.
- Carefully identify the CO2 tank into the chiffonier and shut the door.
Now that your kegerator is in identify and ready to utilise, set a schedule to maintain your beer system and ensure your taps and beer lines stay clean. Inspect the CO2 levels on your tank regularly and check the PSI gauge to make sure the pressure level is at the right level. With proper maintenance, your beer dispenser will provide many years of service.
Source: https://www.webstaurantstore.com/article/515/how-to-set-up-a-kegerator.html
0 Response to "How To Set Up A Keg"
Post a Comment